Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes

Tools

RockShox Charger Damper Bleed Kit
$40.00
Periodic hydraulic damper bleeds are necessary to maintain consistent performance. RockShox's Charger Damper Bleed Kit has everything you need to keep your Charger-equipped fork charging hard.
RockShox Dust Seal Installation Tool
$21.00
- Used to install fork dust seals
RockShox Fork Service Kit
$17.00
Service kits include dust seals, foam rings, oil seals, air and damper o-rings needed for basic service.
ProGold Bike Wash
$9.00
- Consumer grade spray cleaner removes dirt and grime - Safe on all parts including carbon
ProGold Blast-Off Degreaser
- Progold's powerful degreaser formula in a ready-to-use aerosol can - Quickly cleans bicycle components with no scrubbing or rinsing - Leaves behind no oily residue
ProGold Degreaser And Bike Wash
$12.00
- Concentrated degreaser and wash that cleans grime, oil and greases gently - Safe on all surfaces
ProGold EPX Cycle Grease
$6.70
- Exceptional friction reduction and anti-wear properties with greatly reduced friction in metal to metal applications
ProGold Foaming Citrus Degreaser
- Water based foaming degreaser with high solvency and clinging properties - Degreases lubricated parts quickly and effectively - Supplied with extension tube for pinpoint application
ProGold Progold Chain Gauge
$24.00
- Accurate inexpensive gauge measures wear/elongation of most chains
PowerTap G3 Hub Cap Removal Tool
$9.99
- Allows rider to update firmware in G3 PowerCap. - Allows rider to change the hub’s CR2032 battery. - Used for the removal of the G3 PowerCap. - Removes the G3 PowerTap cap to update the firmware or change the hub’s CR2032 battery.
Pedro's BB Socket Holder
If you have even battled with an over-tightened Shimano and ISIS Drive splined bottom bracket cup, you know why Pedro's created the BB Socket Holder. Though these types of bottom brackets proved themselves as the standard for many years and continue to be found on many bikes, the tendency for these shallow splines to slip during removal or installation has resulted in more than a few expletives, high frustration levels, and worst of all, injuries. Pedro's BB Socket Holder provides a simple, shop quality tool that solves this problem. Backed by Pedro's lifetime warranty. - Holds socket tool to BB axle to eliminate slippage during removal and installation - Works with square taper and splined axles with M8 or M15 internal spindle thread - Made from heat-treated tool steel for the ultimate in strength and long-lasting performance - Use with Pedro's Splined Bottom Bracket Socket. Compatible with Pedro's Pro Socket Handle.
Pedro's Cone Wrench
$10.00
Professional quality heat-treated steel with hand-saving no-slip plastic grip and ergonomic design for maximum leverage and comfort. - Precision cut for an exact fit with no slippage - Lifetime warranty on all Pedro's tools
Pedro's Folding Hex/Screwdriver Set
Pedro's folding wrench sets are essential for the shop, event, ride, and at home. These folding wrench sets feature professional grade tool steel for strength, superior anti-corrosion finish for unmatched lasting performance, and body made of lightweight but super tough composite material. The new body features improved ergonomics, shaped to perfectly fit in your hand, allow easy access to each tool, and with extra length for better leverage and control. In addition, the new stay-tight bolt design keeps tool bits from loosening over time. The Folding Hex/Screwdriver Set weighs 120 grams and has 7 tools: 2.5, 3, 4, 5 and 6mm hex wrenches and flat-blade and #2 Phillips screwdrivers. Backed by Pedro's lifetime warranty. - 120 gram, 7-function shop quality folding tool with 2.5, 3, 4, 5 and 6mm hex wrenches and flat-blade and #2 Phillips screwdrivers - Super strong composite body features new design with improved comfort, better leverage, and stay-tight bolt design - Professional-grade tool steel wrenches feature superior anti-corrosion finish for unmatched lasting performance
Pedro's Hex Driver
$25.00
- Specifically designed for quick and easy installation and removal of various bicycle parts and accessories - Ergonomic dual-density screw driver handle - Features extra long hex key and second ball-end - Designed to stand up to the harsh conditions of professional use
Pedro's L Hex Wrench Set
$35.00
The hex wrench is the most common tool needed for the modern bicycle. Choosing the right set can make the difference between good day and a bad day working on bikes. Pedro's L Hex Wrench Set is up to the challenge. They made these wrenches from heat-treated SNCM-V alloy steel to ensure superior strength and long-lasting performance. Pedro's hex wrenches also feature extra length and a round-style end for better leverage and easy access and handling of hard-to-reach bolts. The set includes all the sizes you need in a convenient holder. - Made from heat-treated SNCM-V alloy steel to ensure long-lasting performance - Extra length provides great leverage and access to hard-to-reach bolts - Includes: 1.5, 2, 2.5, 3, 4, 5, 6, 8, & 10mm sizes in convenient holder
Pedro's Rx Micro-9 Multitool
$35.99
- Micro Lever Compatible - Backed by Pedro's Lifetime Warranty and Rust-Free Guarantee - Hex Wrenches: 2.5, 3, 4, 5, 6, 8mm - T25 and T30 torx - Flat blade screwdriver - 95 grams Pedro's new Rx Micro multi-tool is ready for trailside repairs and daily adjustments and delivers the perfect balance of size, weight, and function. It's designed for performance and durability with a 6061 aluminum body, premium CrMo tool steel bits, and an anti-corrosion finish backed by our Rust-Free Guarantee.
Pedro's Screwdriver Set
These professional-grade screwdrivers are designed for ease of use, comfort, and lasting durability. - Five-Piece Set Includes: #1 and #2 Phillips plus 4.5, 5.5, and 6.5mm flat-blade screwdrivers and storage pouch. - Two-Piece Set Includes: #2 Phillips and 5.5mm flat-blade screwdrivers - Dual-density, ergonomic thermoplastic handles for comfortable grip and leverage. - Heat-treated tool steel construction for strength and durability.
Pedro's Vise Whip
$65.00
Do you just LOVE fumbling with awkward tools, slamming your knuckles into sharp gear teeth, and making tasks harder than they should be? If so, you should stop reading and give your chain whip a big hug! However, if you've been looking to throw your chain whip into the woods, never to be seen again, you've come to the right place. Pedro's Vise Whip is simply a better solution for holding your cassette during removal. This innovative tool was developed by Pedro's in-close collaboration with legendary frame builder and cycling technical author Lennard Zinn. The Vise Whip is beautifully simple to use, adjusts to fit 11-23 tooth gears on all multi-gear cassettes (including 11-speed), and locks in place during use. Once you try it, you'll never go back to a chain whip again. - Secure, no-slip, no bloody knuckles, way to hold cassette during removal - once you try it you'll never go back! - Made from heat-treated tool steel for the ultimate in strength and long-lasting performance - Adjustable to fit 11-23 tooth gear sizes - Compatible with all multi-gear cassettes including 11-Speed
Park Tool 1.7mm Straight Internal Snap Ring Pliers
$23.95
Professional quality ring plier made from forged, heat-treated cro-moly steel with a return spring and vinyl dipped grips. The RP-5 has 1.7mm tips on straight blades for small, internal snap rings. The tips open from 22mm to 0 (tips touching).
Park Tool 11-Speed Compatible Chainwhip/Sprocket Remover
$30.49
Park's 11-Speed Compatible Chainwhip/Sprocket Remover is for removing cassettes and freewheels, and getting cogs apart, too. It has a long plastic-covered handle for excellent leverage and the chain is attached with hardened pins for durability. The chain fits on everything from 11- to 5-speed cassettes and freewheels.
Park Tool 50th Anniversary 3-Way Hex Wrench
This is a limited edition version of Park Tool's world famous “Y” wrench. The AWS-50 features a forged, two-piece aluminum body anodized in Park Tool Blue with a laser engraved logo. Hexes are made of industrial strength, heat-treated steel and gold plated to commemorate Park's 50th anniversary.
Park Tool AWS-1 3-Way Hex Wrench - 4mm/5mm/6mm
$12.49
Park Tool introduced the bicycle world to the 3-way hex wrench set over 30 years ago. Our 3-way wrenches fit perfectly in the palm of the hand and provide excellent leverage, making them a favorite of countless shop mechanics worldwide. AWS-1 FEATURES - 4mm, 5mm, and 6mm hex set - Wrenches made from industrial tool steel, through hardened and tempered for long life - Chamfered tips for a perfect fit
Park Tool AWS-3 3-Way Hex Wrench - 2mm/2.5mm/3mm
$11.49
Park Tool introduced the bicycle world to the 3-way hex wrench set over 30 years ago. Our 3-way wrenches fit perfectly in the palm of the hand and provide excellent leverage, making them a favorite of countless shop mechanics worldwide. AWS-3 FEATURES - 2mm, 2.5mm, and 3mm hex set - Wrenches made from industrial tool steel, through hardened and tempered for long life - Chamfered tips for a perfect fit
Park Tool Axle and Spindle Vise Inserts
A great shop accessory made to hold a wide variety of axles, spindles and any Park Tool Freewheel Remover/Lockring Tool. Made from precision extruded aluminum.
Park Tool BBT-69.2 Bottom Bracket Tool
$26.95
Precision CNC machined aluminum tool for the installation and removal of 16-notch external bearing bottom brackets. Featuring updated tooth profiles to optimize the fit between the tool and high performance BB parts. Anodized and laser engraved for easy identification and featuring a ratchet/torque wrench compatible 3/8-inch drive. - 16 notch 44mm OD cups - Fits Shimano BB80, BB5700, XT BB70, BB51, and previous external bearing threaded cups - Also fits many external threaded types for Campagnolo, Chris King, FSA MegaExo, Hope, SRAM/Truvativ GXP, Race Face X-type, Surly, Wheels, Fulcrum, and others - Fits 16 notch rotor disc lockrings
Park Tool BKD-1 Hydraulic Brake Bleed Kit
The BKD-1 Hydraulic Brake Bleed Kit will bleed most models of DOT-fluid-based hydraulic brakes. Hydraulic systems need bleeding to remove any air bubbles and to inject new, clean fluid. - Designed and built for home use and the rigors of daily commercial use - Includes two syringes, hoses with shutoff clips, multi-size bleed blocks and a unique attachable syringe mount - Housed in a rugged reusable case - Machined stainless steel and 7075 aluminum fittings to service SRAM, Hayes, Formula, Hope and other brands of DOT-fluid-based hydraulic brake systems - Replacement parts available - Brake fluid not included
Park Tool Bike Cleaning Brush Kit
$21.95
A clean bike is a happy bike! Park Tool's Bike Cleaning Brush Kit is a four-piece brush set designed specifically to clean bicycles. Ergonomically designed and featuring dual-density, sure-grip handles, the BCB-4.2 kit includes: • 1 GSC-1 Gear Clean Brush • 1 Tapered Detail Brush • 1 Frame Cleaning Sponge/Bristle Brush • 1 Soft Bristle Soaping Brush
Park Tool Bottom Bracket Bearing Tool Set
$37.34
Park's Bottom Bracket Bearing Tool Set removes and installs (with a bearing press, which is sold separately) BB30, PF30, EVO 386 and BBright bottom bracket bearings. This fine tool slides through the bottom bracket shell and into the bearings so the bearings can be tapped out with a hammer. Two bushings for installing BB30 and PF30 bearings from SRAM and FSA are included (press required and sold separately).
Park Tool Bottom Bracket Tool
$46.95
Precision CNC machined dual-sided aluminum tool for the installation and removal of 12- and 36-notch external bearing bottom brackets. Anodized for easy identification and featuring a ratchet/torque wrench compatible 3/8-inch drive. Fits Praxis M30 and M35 - M30: 12-notch 48mm OD cup - M35: 36-notch 51.7mm OD cup
Park Tool Bottom Bracket Tool
$29.95
Precision CNC machined aluminum tool for the installation and removal of 12-notch external bearing bottom brackets. Anodized for easy identification and featuring a ratchet/torque wrench compatible 3/8" drive. - 46mm 12-notch OD cup - Race Face® Cinch™, Rotor® BSA30, Zipp® Vuma™, Hawk Racing™ BB3086™, and more